FORE  &  AFT  MARINE

             WAXES         

    "for the Wet Look"

     BOATS  

    MOTOR HOMES

    AIRPLANES

    • "Highest initial gloss of all do it yourself products tested." 
    • "Highest gloss after 12 months." 
    • "Highest gloss after maintenance coats." 
    • "Highest gloss after removal and reapplied." 
       
        Ease of removing, "Excellent" 
      Practical Sailor, a consumer resource (07/98)

      "POLIGLOW is one of our favorites" 

     Power Boat Report (07/98)
      "Of the DIY products tested, Poli-Glow, New Glass, and Vertiglass show the most gloss and last longest."
     Power Boat Report (04/99)

        Look at that reflection!
    (Note how bad the hull looks below the water stripe)

    That's why Power Boat Report  rated it the best of the do-it-yourself products in its 12-month test published 4/99.
     EASY APPLICATION - Wipe on, NO RUBBING or BUFFING

    LONG LASTING -  Lasts for over 12 Months - POLI GLOW will not wash off with soap and water

    POLI GLOW is NOT a Wax -  POLI GLOW is a new concept in boat polish
     
     
    Complete Starter Kit - $ 49.95
    Includes everything needed to do a 32' boat - 32 oz Poli Glow, 32 oz Poli Prep, 7" Applicator, Scrubby Pad & Instructions
     

    GUARANTEE

    If you are not totally satisfied with POLI GLOW, simply return  unused portion with applicator for a full refund.

    PREPARATION

    The Most Important Step

    Do not use rubbing or polishing compound(s) to clean the boat. Poli Prep is a concentrate cleaner (wear rubber gloves). Do not use full strength. Dilute three parts water to one part Poli Prep. Wet surface with water. Apply Poli Prep with trigger sprayer and scrub vigorously. Oxidation and stains must be removed (Poli Glow will seal in any stains on the surface, i.e. shiny rust stains) All colors have to be uniform with no light variations. Colored areas sometimes get a sunburned film or bleached layer over them. This needs to be removed. The surface does not need to be shiny for the application of Poli Glow, just clean and uniform in color. Let dry for one hour before applying Poli Glow.

    APPLICATION OF POLI GLOW

    Minimum of five coats. Each coat will dry in approximately one minute. There are two applicators, a small one for hard to reach areas and a large applicator. The large applicator can be fastened to any threaded pole for easy application

    Do not treat Poli Glow like a wax. Apply Poli Glow, instead like a paint or varnish. It should be applied to the surface gently. Do not push down on applicator, this may cause foam or bubbles which may dry rough. Do not stop applicator, instead pull away from surface gradually. If drips occur, remove them with applicator before they dry. Avoid windy conditions.

    Now it is time to apply Poli Glow. This is the easy part. Apply Poli Glow to the applicator amd allow a minute to soak into applicator. Pick a small 2' x 2' flat surface to see what Poli Glow will do. Working in small sections (3-4 foot), lightly wipe Poli Glow onto the surface in thin, even, overlapping strokes. Make sure application is dry, approximately one minute at 55 - 95 F, before applying the next coat. If you go over Poli Glow before it is dry you will get brush marks. Apply a minimum of five coats. The first two or three coats may appear dull or streaky due to penetration into the fiberglass. Poli Glow may be applied in direct sunlight except with dark colors. When overlapping you may see areas that are shinier. They will disappear in 24-48 hours. Avoid contact with rain for several hours. If water spots occur they will disappear after a few hours in the sunlight.

    PG32(LIST $44.95)$39.95  32 oz. Poli Glow

    PG32A(LIST $64.95)$54.95  32 oz. Poli Glow Kit, Poli Prep, Scrub Pad,7" Applicator 

    PGPC(LIST $16.95)$14.95  32 oz. Poli Prep Cleaner

    PGAP(LIST $9.95)$7.95  7" Poli Glow Applicator 

    RETURN TO WAX MENU

    RETURN TO MAIN MENU